Folder: Licensed Drivers for HD over IP Dealers

• 

  Control4 Driver for Dell Power Connect 12x12

  Uploaded:

  25.06.11

  Modified:

  25.06.11

  File Size:

  64 KB

  Version:

  1.8.6.18

  This driver is Just Add Powers intellectual property and/or copyrighted content. It is intended solely for use with Just Add Power. Any other unauthorized use is strictly prohibited and will be prosecuted as violations of our copyrights and as theft of our confidential intellectual property.

  
  

  Instructions: 

  
  

  Connect the included RS232 cable or your own null modem cable to the switch and the Control4 controller. Go to the connections tab and make the RS232 binding. Go to the System Design tab and click on the driver. on the top of the driver click the Actions tab and Get SVC Tag. Go back to the properties page and look for the Service Tag ID. Email your Service Tag ( which can be found on the properties tab ) to This e-mail address is being protected from spambots. You need JavaScript enabled to view it We will respond with your activation key.

  
  

  Once you receive the keycode paste it into the key area and click set. The driver should now say License Verified. Once verified set the properties of the switch. If you are using a gigabit switch you need to set gigabit to true and press set button. This will allow the driver to communicate with the gigabit version ( Dell 54xx and 62xx ). The 35xx series switches need the driver set to false. If you are using 2G products set the 2G setting to True. If you are using a gigabit switch and 1st Gen product make sure the 2G is set to false. Once those settings are done click on the actions tab in the driver and click Initialize Switch. Then go to the connection tab and do your HDMI bindings and then refresh navigator. Your Done!

  
  

  Error Message Unable to obtain service tag from switch:

  
  

  Check that you are using a NULLModem Serial cable. The one included with the switch is nullmodem. If you are making your own cable pins 2 and 3 need to swapped on one end. Once verified unplug the serial cable from the switch and power cycle the switch then wait 3 minutes and plug the serial cable back in. Go to actions and click Get SVC Tag. If you are still having issues after this contact support. 

  
  

  

  Download Details
• 

  Control4 Driver for Dell PowerConnect 24x24

  Uploaded:

  18.05.11

  Modified:

  25.06.11

  File Size:

  79 KB

  Version:

  1.8.6.18

  This driver is Just Add Powers intellectual property and/or copyrighted content. It is intended solely for use with Just Add Power. Any other unauthorized use is strictly prohibited and will be prosecuted as violations of our copyrights and as theft of our confidential intellectual property.

  
  

  Instructions: 

  
  

  Connect the included RS232 cable or your own null modem cable to the switch and the Control4 controller. Go to the connections tab and make the RS232 binding. Go to the System Design tab and click on the driver. on the top of the driver click the Actions tab and Get SVC Tag. Go back to the properties page and look for the Service Tag ID. Email your Service Tag ( which can be found on the properties tab ) to This e-mail address is being protected from spambots. You need JavaScript enabled to view it We will respond with your activation key.

  
  

  Once you receive the keycode paste it into the key area and click set. The driver should now say License Verified. Once verified set the properties of the switch. If you are using a gigabit switch you need to set gigabit to true and press set button. This will allow the driver to communicate with the gigabit version ( Dell 54xx and 62xx ). The 35xx series switches need the driver set to false. If you are using 2G products set the 2G setting to True. If you are using a gigabit switch and 1st Gen product make sure the 2G is set to false. Once those settings are done click on the actions tab in the driver and click Initialize Switch. Then go to the connection tab and do your HDMI bindings and then refresh navigator. Your Done!

  
  

  Error Message Unable to obtain service tag from switch:

  
  

  Check that you are using a NULLModem Serial cable. The one included with the switch is nullmodem. If you are making your own cable pins 2 and 3 need to swapped on one end. Once verified unplug the serial cable from the switch and power cycle the switch then wait 3 minutes and plug the serial cable back in. Go to actions and click Get SVC Tag. If you are still having issues after this contact support. 

  
  

  

  Download Details